Supacat Mk IIa 1900 TD 6X6 Fitted With 2 Ton Palfinger Crane

6x6 high mobility load carrier fitted with a 2 ton Palfinger fully hydraulic crane, Warn recovery winch and self loading ramps .
The Supacat has been fully serviced to include, a full cambelt change, new oil, fuel and air filters, new seats and three point seat belt harness. The Supacat 6x6 1900 TD has permanent six wheel drive (6x6) with the front four wheels (two axles) steered conventionally (Ackerman) by using a rotating handlebar arrangement. These handlebars also operate the steering brakes (inboard discs) which act independently on each side of the vehicle giving brake (skid) steering. The Supacat is diesel powered and driven through a torque convertor, three forward and one reverse ratio automatic gearbox and a single differential. Twin output shafts transmit the drive to the two drop gear reduction boxes, which carry the inboard disc brakes. The centre axle is shaft driven direct from the drop gearbox. The centre axles carry the outboard, foot pedal operated disc brakes which are effective on all wheels. The final drive to the front and rear wheels is by heavy duty one inch pitch duplex chains. The Supacat is built around a steel rectangular hollow section (RHS) chassis frame which forms the entire shape of the vehicle and to which all components and attachments are fitted. The body of the Supacat is made from graded aluminium and forms a hull which enables the vehicle to float and protects the majority of mechanical components. The belly plate is of 5mm hardened aluminium. Supacat 6x6 1900 MK IIa - Technical Specification ENGINE - 1900 TD Make - Volkswagen 1.9 TD Fuel - diesel Cylinders - four (4) GEARBOX Type – 3 speed automatic TORQUE CONVERTER - (Integral with gearbox) Make - Supacat DROP GEARBOXES - (Two, one each side) FRONT AXLE Make - Supacat Type - Chain driven from centre axle, one on each side of vehicle with steerable hub. CENTRE AXLE Make - Supacat Type - Common to drop gearboxes, shaft driven steerable hub with disc brake. DRIVE CHAINS Type – 1" pitch duplex gear, four identical chains per vehicle. STEERING - (Ackerman) Make - Supacat Type - Handle bar operated, power assisted STEERING - (Brake) Make - Supacat / AP. Type - Handlebar operated hydraulic, onto inboard discs, one per side controlling all wheels on that side through transmission. Type - Transmission lock integral with gearbox. SUSPENSION ELECTRICS Power - 12 volt Alternator - 65 amp Battery - 66 amp hour Starter motor - 1.8 Kw ELECTRICAL COMPONENTS horn, lights, indicators, rear fog light, cold start, hazard warning, (bilge pumps, convoy lights, winch, winch/intervehicle start power plug, auxiliary lights, auxiliary power output) LIGHTING - Head, side, tail, brake, indicators, to UK road legal requirements. WHEELS Type - Steel centre and reinforced rim Size - 13 x 15 TYRES Size - 31 x 15.5 x 15 (Section width 389mm, O/D 788mm) Ply rating – 4-8 ply Tubes - Tubed or tubeless Construction - Cross ply Sealant - Optional in tubeless CONSTRUCTION Chassis frame - Welded steel rectangular hollow section of various dimensions. This incorporates lifting / towing points which may be used for helicopter underslinging. Parts of the frame are accessible and may be used for the attachment to and / or support of additional equipment. Load securing points are also incorporated. Body panels - Aluminium plate of various grades of hardness and thickness according to position and duty. Some are riveted onto the frame, others are removable. Some GRP is also used. Belly plate - One piece, 5mm half hard aluminium plate extending from the front panel, under the entire vehicle to just below the tailgate. TOWING CAPACITY The Supacat is capable of producing approximately 2 tonnes of drawbar pull in ideal conditions.
FLUID CAPACITIES - Fuel 50 litres (11 galls) - Engine oil 4.5 litres - Coolant 10 litres - Front axle 0.5 litre (each) - Drop gearbox 1.25 litres (each) - Chassis lube 2 litres - Gearbox 2.5 litres - Differential 0.75 litres - Power steering 2 litres DIMENSIONS All dimensions in millimetres (mm). - Overall length, 3335 (minimum) - Overall length, 3440 (with NATO hitch) - Overall width, 2000 (wheel to wheel) - Overall width, 1870 (vehicle structure) - Maximum height, 1895 (open vehicle) - Maximum height, 2010 (cabbed vehicle) - Minimum height, 1210 (non cabbed folded) - Wheel base, 1846 - Wheel track 1601 (centre to centre) - Platform height, 940 - Load area, 1445 x 1870 - Ground clearance 215 (on wheels) - Ground clearance 316 (on tracks) - Angle of approach 57 degrees - Angle of departure 58 degrees - Ramp length, 2690 (optional extra) - Height of two Supacats stacked & folded 2150 - Fording depth laden approximately 860 mm - Unladen vehicle floats at approximately 700 mm depth of water. WEIGHTS Basic Supacat - 1690 Kgs (calculated)
PRICE ON APPLICATION

https://youtu.be/4QCR2xxGUOg


Philip Caple: 01823 673396 or 07736 807892

Other Webverts from this Advertiser:




This MILWEB WEBVERT costs just £25 and is displayed for 2 months. WEBVERTS are open to trade and private advertisers from around the world. Your own page with up to 6 pictures will make your advert stand out from the crowd. With over 48,500 visits a week, it really pays to advertise on MILWEB.